Hot water heater maintenance and safety tips – Your water heater may remain relatively unseen, usually hidden away in a utility closet or sitting alone in a basement or garage, but keep in mind that it needs regular maintenance for safety reasons. So, make sure yours is safe, by getting to know its parts and learning some important facts.
Water heater parts
Now most residential tanks can hold 40 to 60 gallons and need to withstand the pressure of a residential water system (typically 50 to 100 psi.) Steel tanks are tested to handle 300 psi and have a bonded glass liner to keep rust out of the water, as well as insulation surrounding the tank. Sort of your high end water heater there. Other water heater parts include:
- A dip tube to let cold water into the tank
- A pipe to let hot water out of the tank
- A thermostat to control the temperature of the water inside the tank
- Heating elements similar to those inside an electric oven
- A drain valve that allows you to drain the tank to replace the elements, or to move the tank
- A temperature or pressure relief valve that keeps the tank from exploding
- A sacrificial anode rod to help keep the steel tank from corroding
Temperature or pressure relief valve
Temperature or pressure relief valves help prevent tanks from exploding if temperature or pressure exceeds safe limits. Unfortunately, residential valves can be prone to failure, so test this valve yearly by:
- Pulling up on the handle to make sure water flows freely out, and stops when you let go of the handle. If it does nothing or runs or drips, then the valve should be replaced.
- Flushing the hot water heater through the drain valve to remove sediment buildup. You should have a drain line, either plumbed outside or within about 6 inches of the floor to prevent you from being scalded if the valve opens while you’re next to it.
Temperature control
On residential tanks, the settings are normally warm, hot, very hot or something similar. There is so much variation on what these settings mean, but the right temperature is around 120 degrees at the tap, which you can test with a kitchen thermometer.
It is important to keep the temperature close to 120 degrees to kill germs and prevent children from being scaled. Compared to adults, babies and children have thinner skin that burns faster and at lower temperatures. It’s a good idea to check the water temperature using your wrist or elbow every time you bathe a baby, toddler or young child. For more information about preventing burns and scalds to children visit Make Safe Happen.com.
When leaving for vacation, set the hot water heater temperature to its lowest setting. This saves money and reduces the risk of problems while you are away.
Vents
Poor ventilation can cause fumes and carbon monoxide to reenter the room instead of going outside. This can expose family members and even pets to danger. To maintain good ventilation make sure of the following:
- The vent is the same diameter as the tank’s draft diverter
- The vent goes straight up and out, without any dips
- Where it passes through walls or roofs, it is double-walled. Single-walled vent sections should be screwed with 3 screws per section, especially in earthquake zones.
Earthquake straps
Now, while not USUALLY an issue in South Carolina (a 4.1-magnitude quake struck the low country of McCormick County in 2014 though). Strapping your water heater is a good idea, even if you aren’t worried about THE BIG ONE. Storms and other natural disasters can create a hazard and hey, better safe than sorry right? This is particularly important for maintaining gas water heater safety. If your water heater were to fall over, it could sever the gas line and cause an explosion.
Additional water heater safety tips
Keep safe by following these water heater recommendations:
- Remove paper, dust or other combustibles from the heater enclosure.
- Extinguish the pilot light before using flammable liquids or setting off aerosol bug bombs.
- If the device is in the garage, raise it so the pilot light is 18 inches above the floor. This helps prevent ignition of gasoline vapors that collect near the floor.
- Consider installing an automatic gas-shutoff valve to stop the flow of gas if the ground moves or if gas flow increases dramatically. The valve prevents fires when a gas line breaks due to flood, earthquake or other disaster.
- You may want to insulate the first six feet of the hot water pipe and the first three feet of the cold water pipe that extends from your hot water tank. Insulation reduces heat loss on the hot water pipe and “sweating” on the cold water pipe.
- Do not use pipe wrap or any other insulation within six inches of the draft hood or flue exhaust vent at the top of the natural gas water heater.
That should be about it. Just practice common sense and if you have ANY questions, reach out to the pros at BUDGET PLUMBING. They are ready and able to answer ANY & ALL of your plumbing questions. Give Tom & Robert a call at 864-250-0700.
